HOME PAGE ABOUT US R&D OUR TEAM QUALITY CONTROL JOIN US CONTACT US
Product Catalogue
 
Battery Management        
Electrical Accessories    
Automotive Fault Diagnosis Instrument
Wiring Harness
Exhaust Gas Recirculation
Customer Services
 
Direct Enquiry
Quality
Services and Support
Trade Shows
Distributors
Catalogue
Test Report PDF
HOME  >  PRODUCTS
Path    >    Electrical Accessories    >    Automotive Relay
Article No.: 784
Download PDF File
 
Feature
 
  Fiat Parts
according to FIAT 9.90110 and 9.91320/02
 
  Material
 
  1. Plate: PA66-GF35
2. Housing: PA66-GF35
3. Bolt to terminal 30: brass (CuZn)
 
Temperature range of environment:
 
 
  • operating temperature -40 ... +105°C
  • storage temperature -40 ... +125°C
  •  
    Electrical characteristic data:
     
     

    6V @ +105°C - 16V @ +105°C normal operation of GCU (GCU = glow control unit)
    6V @ -40°C - 16V @ -40°C normal operation of GCU
    0,5 V Voltage drop of electronic
    < 5,5V @+105°C pull in voltage electrical relay
    the pull in voltage electrical @ -40°C and @ +25°C must be < 5,5V
    recommendation: the pull in voltage magnetical should be in the range of the pull in voltage electrical
    recommendation: release voltage relay > 2V @ -40°C...+105°C
    Sink current on faston 86 <10000 mA
    Sink current on faston ST/K <50 mA
    Sink current on faston DI (Open Collector max 10mA)
    Maximum switch current on faston 30 275 A max. 1s
    Maximum switch current on fastons G1....G5 55 A x 5 max. 1s
    Voltage drops terminal faston 30 and G1...G5 <=200mV at 10A (7,5A at each Gx)

     
    Short circuit consistency
     
     

    Max. switched current of relay: 600 A / 12V
    All connections except G1 to G5 of GCU to ground (term 31) and Ubatt unlimited in time
    Short circuit protection G1 to G5 by electronical fuse, if at minimum one plug current is higher than
    Iswitch , the whole load circuit is switched off.
    Iswitch min 30 A for each Gx
    Iswitch max 55 A for each Gx
    Ubatt 12V

     
    Resistance of shunts
     
     

    Shunt 1 : 5.4 mOhms 10%
    Shunt 2 : 5.4 mOhms 10%
    Shunt 3 : 5.4 mOhms 10%
    Shunt 4 : 5.4 mOhms 10%
    Shunt 5 : 5.4 mOhms 10%

     
    Valid documents
     
     

    As far as there are no other definitions given in this specification, the relevant specifications given in the
    following documents are valid.

    Document type Document p/n Title
    Procurement specification (CFO) 9.01102 Quality of supplies Fiat Auto spa
    Procurement specification (CFO) 9.01102/08 Statistical process control
    Procurement specification (CFO) 9.01102/09 Electronic control system. Supplier's technical documentation
    Procurement specification (CFO) 9.01102/10 Classification criteria for products and their characteristics.
    Procurement specification (CFO) 9.01103 Product quality and conformity certificate.
    Procurement specification (CEL) 9.90110 Automotive electrical and electronic devices.
    Procurement specification (CEL) 9.92318 Electronic device for glow plug control
    Procurement specification (CEL) 9.91180 Printed circuits
    Procurement specification (CEL) 9.92210 Relays
    Design standard (CEL) 80209 Connectors
    Design standard (TFO) 00167 Danger/prohibition and warning/obligation symbols on vehicle components.
    Design standard FGPS 0100 Notation of date in documents and drawings
    Design standard FGPS 1100-5 Sheet sizes and subdivisions of the drawing sizes
    Design standard FGPS 1110 Word abbreviations/entries in revision history of drawings
    Design standard FGPS 1200 Part Identification-General rules
    Design standard FGPS 1201 Part Identification - Notation of manufacturing date.
    Design standard FGPS 1210 Part Identification - Marking of parts made from polymeric materials
    Design standard FGPS 1100-7 Entries of KPC/PQC in drawings
    Design standard (TFO) 01390/01 Tightening torque for metric-thread bolts tightened up to pre-set torque.
    Design standard (TFO) 07247 Cad drawings autonomous quality certification of CAD parts (check-list).
    Design standard (PRO) 07412 Marking of motor vehicle components. Guideline.
    Design standard (TFO) 07416 Recycling markings for plastic, composite and elastomer components.
    Design standard (TFO) 07471 Provisions identification of drawings subject to law provisions, qualification and anti-pollution system.
    Design standard (TFO) 07611 Supplier alphanumeric code marking - Indications on drawings.
     
     
     
    ABOUT US    |    PRODUCTS    |    R&D    |    QUALITY CONTROL    |    CONTACT US
    Copyright © 2009 AOPEC. All Rights Reserved